Driven and parasitic elements

Part of a series on
Antennas
Common types Dipole Fractal Loop Monopole Satellite dish Television Whip
Components Balun Block upconverter Coaxial cable Counterpoise (ground system) Feed Feed line Low-noise block downconverter Passive radiator Receiver Rotator Stub Transmitter Tuner Twin-lead
Systems Antenna farm Amateur radio Cellular network Hotspot Municipal wireless network Radio Radio masts and towers Wi-Fi Wireless
Safety and regulation Wireless device radiation and health Wireless electronic devices and health International Telecommunication Union (Radio Regulations) World Radiocommunication Conference
Radiation sources / regions Boresight Focal cloud Ground plane Main lobe Near and far field Side lobe Vertical plane
Characteristics Array gain Directivity Efficiency Electrical length Equivalent radius Factor Friis transmission equation Gain Height Radiation pattern Radiation resistance Radio propagation Radio spectrum Signal-to-noise ratio Spurious emission
Techniques Beam steering Beam tilt Beamforming Small cell Bell Laboratories Layered Space-Time (BLAST) Massive Multiple-input multiple-output (MIMO) Reconfiguration Spread spectrum Wideband Space Division Multiple Access (WSDMA)
v t

In an antenna array made of multiple conductive elements (typically metal rods), a driven element or active element (also called driven radiator or active radiator) is electrically connected to the receiver or transmitter while a parasitic element (or passive radiator) is not.

This section does not cite any sources. Please help by adding citations to reliable sources. Unsourced material may be challenged and removed. (April 2016) (Learn how and when to remove this message)

In a multielement antenna array (such as a Yagi–Uda antenna), the driven element or active element is the element in the antenna (typically a metal rod) which is electrically connected to the receiver or transmitter. In a transmitting antenna it is driven or excited by the radio frequency current from the transmitter, and is the source of the radio waves. In a receiving antenna it collects the incoming radio waves for reception, and converts them to tiny oscillating electric currents, which are applied to the receiver. Multielement antennas like the Yagi typically consist of a driven element, connected to the receiver or transmitter through a feed line, and a number of other elements which are not driven, called parasitic elements. The driven element is often a dipole. The parasitic elements act as resonators and couple electromagnetically with the driven element, and serve to modify the radiation pattern of the antenna, directing the radio waves in one direction, increasing the gain of the antenna.

An antenna may have more than one driven element, although the most common multielement antenna, the Yagi, usually has only one. For example, transmitting antennas for AM radio stations often consist of several mast radiators, each of which functions as a half-wave monopole driven element, to create a particular radiation pattern. A two-element array with the elements spaced a quarter wavelength apart has a distinct cardioid radiation pattern when the second element is driven with a source −90° out of phase relative to the first element. A log-periodic antenna (LPDA) consists of many dipole elements of decreasing length, all of which are driven. However, because they are different lengths, only one of the many dipoles is resonant at a given frequency, so only one is driven at a time. The dipole that is driven depends on the frequency of the signal. Phased arrays may have hundreds of driven elements. Household multiband television antennas generally consist of a hybrid between a UHF Yagi with one driven dipole and a log-periodic for VHF behind that with alternating active elements. The driven elements between the UHF and VHF are then coupled and often matched for a 75 Ω coaxial downlead to the receiver.

When a "driven element" is referred to in an antenna array, it is often assumed that other elements are not driven (i.e. parasitic, passive) and that the array is tightly coupled (spacing far below a wavelength).

This article needs additional citations for verification. Please help by adding citations to reliable sources. Unsourced material may be challenged and removed. Find sources: "Driven and parasitic elements" – news · newspapers · books · scholar · JSTOR (December 2009) (Learn how and when to remove this message)

In a radio antenna, a parasitic element or passive radiator is a conductive element, typically a metal rod, which is not electrically connected to anything else.^[1] Multielement antennas such as the Yagi–Uda antenna typically consist of a "driven element" which is connected to the radio receiver or transmitter through a feed line, and parasitic elements, which are not. The purpose of the parasitic elements is to modify the radiation pattern of the radio waves emitted by the driven element, directing them in a beam in one direction, increasing the antenna's directivity (gain). A parasitic element does this by acting as a passive resonator, something like a guitar's sound box, absorbing the radio waves from the nearby driven element and re-radiating them again with a different phase. The waves from the different antenna elements interfere, strengthening the antenna's radiation in the desired direction, and cancelling out the waves in undesired directions.

The parasitic elements in a Yagi antenna are mounted parallel to the driven element, with all the elements usually in a line perpendicular to the direction of radiation of the antenna. What effect a parasitic element has on the radiation pattern depends both on its separation from the next element, and on its length. The driven element of the antenna is usually a half-wave dipole, its length half a wavelength of the radio waves used. The parasitic elements are of two types. A "reflector" is slightly longer (around 5%) than a half-wavelength. It serves to reflect the radio waves in the opposite direction. A "director" is slightly shorter than a half-wavelength; it serves to increase the radiation in a given direction. A Yagi antenna may have a reflector on one side of the driven element, and one or more directors on the other side. If all the elements are in a plane, usually only one reflector is used, because additional ones give little improvement in gain, but sometimes additional reflectors are mounted above and below the plane of the antenna on a vertical bracket at the end.

All the elements are usually mounted on a metal beam or bracket along the antenna's central axis. Although sometimes the parasitic elements are insulated from the supporting beam, often they are clamped or welded directly to it, electrically connected to it. This doesn't affect their functioning, because the RF voltage distribution along the element is maximum at the ends and goes to zero (has a node) at the midpoint where the grounded beam is attached.

The addition of parasitic elements gives a diminishing improvement in the antenna's gain.^[2] Adding a reflector to a dipole, to make a 2 element Yagi, increases the gain by about 5 dB over the dipole. Adding a director to this, to give a 3 element Yagi, gives a gain of about 7 dB over a dipole. As a rule of thumb, each additional parasitic element beyond this adds about 1 dB of gain.^[2]

In an example of a parasitic element that is not rod-shaped, a parasitic microstrip patch antenna is sometimes mounted above another driven patch antenna. This antenna combination resonates at a slightly lower frequency than the original element. However, the main effect is to greatly increase the impedance bandwidth of the antenna. In some cases the bandwidth can be increased by a factor of 10.

Not all types of thin conductor multielement antennas have parasitic elements. The log periodic antenna is similar in appearance to a Yagi, but all of its elements are driven elements, connected to the transmitter or receiver.

• ARRL Antenna Book (23 ed.). Newington, CT: American Radio Relay League. 2015. Subsection 11.1. ISBN 978-1625950444.